Electrical safety is a non-negotiable priority of the design, manufacture, and certification of electronic and electrical goods. Leakage current compliance testing is one of the numerous safety parameters that is very important, as it has direct implications on the user safety, approval of that particular product by the regulator, and the reliability of the product. Since this is a detailed guide, it tells about the fundamentals of leakage current, global standards, testing procedures, and best practices that manufacturers and compliance labs like Sunren should follow.
What Is Leakage Current and Why Does It Matter?
- Any unintended current flowing between a live part of an electrical device and ground or accessible conductive parts (e.g., a chassis or enclosure) under normal or fault conditions is leakage current.
- Some leakage of current may occur even when a device is insulated correctly, because no insulator is perfect, and capacitive coupling or design constraints may allow current to leak.
- The excessive leakage current in medical, industrial, and consumer products is potentially hazardous because it can cause an electric shock when a user or a patient comes in contact with the exposed metal parts.
- Leakage current test is a test that checks that this current level should not exceed safe, standardized values, which therefore protects the users and keeps them within the regulatory levels.
Types of Leakage Current
To know how to test and comply, it is important to understand the different types of leakage current Morgan, 1992).
- Earth (Ground) Leakage: Current that flows from the device to earth via the protective ground connection. This is measured with the ground conductor open, simulating a fault.
- Touch/Chassis (Enclosure) Leakage: Current that would flow through a person touching the device’s exposed conductive parts. This simulates direct contact with the product’s enclosure.
- Patient Leakage: Specific to medical devices, this is the current that could flow through a patient connected to applied parts (e.g., electrodes).
- Patient Auxiliary Leakage: Current flowing between different applied parts of a medical device, not intended to have a physiological effect.
Global Standards for Leakage Current Compliance Testing
A variety of international and regional standards regulate the leakage current compliance test, including the areas that an acceptable level can reach:
- IEC 60601-1: Medical electrical equipmentExacting demands: patient and operator safety.
- US standards: US standards based on harmonized IEC standards notably used in the medical equipment and lab equipment, UL 60601-1 / UL 61010-1.
- IEC 60950-1 / IEC 62368-1: Safety of information technology equipment and audio/video equipment.
- North American North American IT and AV equipment have the equivalent UL 60950-1 / UL 62368-1.
- NFPA 99: American Standard concerning electrical systems in any medical facility.
- CSA C22.2: Canadian safety standards for medical and electronic equipment.
- JIS T 0601-1: Japanese Medical electrical equipment.
Every standard sets the level of maximum permissible leakage current depending on equipment class.
Leakage Current Limits: What’s Considered Safe?
Acceptable leakage current levels vary by product type and application:
- General Consumer Products: Typically, the limit is 0.5 mA for accessible parts. For devices with three-prong plugs and warning labels, the limit may be up to 0.75 mA.
- Medical Devices: Limits are much lower due to patient vulnerability. For example, IEC 60601-1 specifies maximum patient leakage currents as low as 10–500 µA, depending on device classification and applied part type.
- Class I Equipment (Grounded): Higher limits (up to 3.5 mA for stationary equipment) are allowed due to the protective earth connection.
- Class II Equipment (Double Insulated): Lower limits (typically 0.25 mA) since there is no earth connection and safety relies on insulation alone.
When Is Leakage Current Compliance Testing Required?
- Type Testing: Performed during the design and certification phase on representative product samples. Required for all mains-powered products seeking regulatory approval.
- Production Testing: For most products, only type testing is needed. However, medical devices require routine production line testing due to higher safety risks.
- Periodic Inspection: Some standards and quality systems require periodic re-testing of installed equipment, especially in medical and industrial settings.
Leakage Current Compliance Testing Procedures
1. Test Setup
- Place the device under test (DUT) on an insulating surface, at least 20 cm from any earthed metal.
- Connect the DUT to the power supply through an isolation transformer.
- Use a measuring device (MD) with input impedance of 1 MΩ and frequency response flat from DC to 1 MHz, simulating the human body.
- Ensure all test leads and the MD are positioned away from unscreened power supply leads and earthed surfaces.
2. Test Conditions
- Normal Operation: Test the device while energized in all normal modes (standby, full operation).
- Single Fault Conditions: Simulate faults such as open ground, reversed line, and neutral, or open neutral, to assess worst-case leakage scenarios.
- For medical devices, also test with the applied parts connected as in actual use.
3. Voltage Application
- Apply supply voltage at 110% of the device’s highest rated voltage and the highest rated frequency. For example, a device rated for 230V 50Hz is tested at 253V 60Hz.
- This ensures safety margins are maintained even in overvoltage conditions.
4. Measurement
- Measure leakage current for each configuration (normal and fault conditions).
- For medical devices, measure earth, enclosure, patient, and auxiliary leakage as appropriate.
- Record the true RMS value with an error not exceeding ±5%.
5. Comparison with Limits
- Compare measured values against the relevant standard’s maximum permissible limits for the product class and use case.
- If any value exceeds the limit, the product must be redesigned or improved before retesting.
Specialized Equipment for Leakage Current Compliance Testing
- Leakage Current Testers: Purpose-built instruments with selectable human body models and high measurement accuracy.
- Hipot Testers: Used for dielectric strength and insulation testing, often performed alongside leakage current tests.
- Partial Discharge Testers: For detecting insulation breakdown at high voltages.
- Isolation Transformers: Provide safe test conditions and allow for controlled fault simulation.
Best Practices for Reliable Leakage Current Compliance Testing
- Calibrate Test Equipment: Specific equipment should be regularly checked and adjusted to comply with norms.
- Operate under Standardized Conditions: Standardized test conditions should be applied as far as possible, and it is imperative to operate under standard test conditions.
- Write it all down: Prepare logs of test conditions, outcomes, and corrective measures in case of audits or regulatory checks.
- Test All Modes: Verify leakage current in all operational conditions and all stated faults.
- Reduce Environmental Interferences: All tests are to be conducted under controlled conditions to eliminate the interference of measuring errors under the influence of humidity, temperature, or off-capacitance.
- Keep in Touch: Regulatory requirements and standards are changing, so keep abreast by reading periodic changes posted by IEC, UL, etc.
Why Leakage Current Compliance Testing Is Critical
- User Safety: Evades the risk of electric shock and particularly where it is simple to be particularly dangerous, such as in a hospital.
- Regulatory Compliance: Needed to certify products and make legal entry to most markets.
- Product Reliability: Detects possible insulation weaknesses and malfunctions in the designs of the products before the experience of the users.
- Brand Reputation: Shows a concern with safety and quality, making the customers and the partners trust.
The Role of Accredited Testing Labs
- Manufacturers interested in having their products certified or gaining market access have their leakage current compliance testing conducted independently and on a standardized basis by accredited labs such as Sunren.
- The considered labs have calibrated equipment of the best technology, applied global best practice, and attained quality results that can be replicated.
- Whereas such labs as Sunren perform even more thorough testing, regulatory authorities and certification organizations give a final OK using test reports.
Frequently Asked Questions
How do you test for leakage current?
Leakage Behavior Leakage current is measured by passing voltage through the device and measuring non-intentional current flow to ground through test probes such as an insulation tester or leakage current tester.
What are the standards for leakage current testing?
Standards for leakage current testing include IEC 60990, IEC 60601, IEC 61010, and IS 13252 (Part 1) in India.
What are the three types of leakage current?
The three types are Earth Leakage Current, Touch (Enclosure) Leakage Current, and Patient Leakage Current (in medical devices).
What is a Class 1 leakage current test?
A Class 1 leakage current test measures current from live parts to protective earth in devices with a ground connection.
Conclusion
The electrical safety of electronics and electrical products, and systems globally rests on leakage current compliance testing. Through the implementation of international standards and standards, the use of accurate procedures, combined with the use of specialized testing equipment, manufacturers and test laboratories are able to warrant that products are still safe to the user and in line with the continuously changing regulations. Leakage current compliance testing is not only a regulatory measure, but it is also a mandatory step in the modern safety-conscious marketplace.
Leave a Reply